![background image](http://html.mh-extra.com/html/cisco/5505-asa-firewall-edition-bundle/5505-asa-firewall-edition-bundle_cli-configuration-manual_186241585.webp)
1-35
Cisco ASA Series CLI Configuration Guide
Chapter 1 Configuring IPsec and ISAKMP
Configuring IPsec
Using Dynamic Crypto Maps
A dynamic crypto map is a crypto map without all of the parameters configured. It acts as a policy
template where the missing parameters are later dynamically learned, as the result of an IPsec
negotiation, to match the peer requirements. The ASA applies a dynamic crypto map to let a peer
negotiate a tunnel if its IP address is not already identified in a static crypto map. This occurs with the
following types of peers:
•
Peers with dynamically assigned public IP addresses.
Both LAN-to-LAN and remote access peers can use DHCP to obtain a public IP address. The ASA
uses this address only to initiate the tunnel.
•
Peers with dynamically assigned private IP addresses.
Peers requesting remote access tunnels typically have private IP addresses assigned by the headend.
Generally, LAN-to-LAN tunnels have a predetermined set of private networks that are used to
configure static maps and therefore used to establish IPsec SAs.
As an administrator configuring static crypto maps, you might not know the IP addresses that are
dynamically assigned (via DHCP or some other method), and you might not know the private IP
addresses of other clients, regardless of how they were assigned. VPN clients typically do not have static
IP addresses; they require a dynamic crypto map to allow IPsec negotiation to occur. For example, the
headend assigns the IP address to a Cisco VPN client during IKE negotiation, which the client then uses
to negotiate IPsec SAs.
Note
A dynamic crypto map requires only the
transform-set
parameter.
Dynamic crypto maps can ease IPsec configuration, and we recommend them for use in networks where
the peers are not always predetermined. Use dynamic crypto maps for Cisco VPN clients (such as mobile
users) and routers that obtain dynamically assigned IP addresses.
Tip
Use care when using the
any
keyword in
permit
entries in dynamic crypto maps. If the traffic covered
by such a
permit
entry could include multicast or broadcast traffic, insert
deny
entries for the
appropriate address range into the access list. Remember to insert
deny
entries for network and subnet
broadcast traffic, and for any other traffic that IPsec should not protect.
Dynamic crypto maps work only to negotiate SAs with remote peers that initiate the connection. The
ASA cannot use dynamic crypto maps to initiate connections to a remote peer. With a dynamic crypto
map, if outbound traffic matches a permit entry in an access list and the corresponding SA does not yet
exist, the ASA drops the traffic.
A crypto map set may include a dynamic crypto map. Dynamic crypto map sets should be the lowest
priority crypto maps in the crypto map set (that is, they should have the highest sequence numbers) so
that the ASA evaluates other crypto maps first. It examines the dynamic crypto map set only when the
other (static) map entries do not match.
Similar to static crypto map sets, a dynamic crypto map set consists of all of the dynamic crypto maps
with the same dynamic-map-name. The dynamic-seq-num differentiates the dynamic crypto maps in a
set. If you configure a dynamic crypto map, insert a permit ACL to identify the data flow of the IPsec
peer for the crypto access list. Otherwise the ASA accepts any data flow identity the peer proposes.
Summary of Contents for 5505 - ASA Firewall Edition Bundle
