1-33
Cisco ASA Series CLI Configuration Guide
Chapter 1 Configuring Inspection of Basic Internet Protocols
SMTP and Extended SMTP Inspection
ESMTP is an enhancement to the SMTP protocol and is similar is most respects to SMTP. For
convenience, the term SMTP is used in this document to refer to both SMTP and ESMTP. The
application inspection process for extended SMTP is similar to SMTP application inspection and
includes support for SMTP sessions. Most commands used in an extended SMTP session are the same
as those used in an SMTP session but an ESMTP session is considerably faster and offers more options
related to reliability and security, such as delivery status notification.
Extended SMTP application inspection adds support for these extended SMTP commands, including
AUTH, EHLO, ETRN, HELP, SAML, SEND, SOML, STARTTLS
,
and VRFY
. Along with the support for
seven RFC 821 commands (DATA,
HELO, MAIL, NOOP, QUIT, RCPT, RSET), the
ASA supports a total
of fifteen SMTP commands.
Other extended SMTP commands, such as
ATRN
,
ONEX
,
VERB
,
CHUNKING
, and private extensions
and are not supported. Unsupported commands are translated into Xs, which are rejected by the internal
server. This results in a message such as “500 Command unknown: 'XXX'.” Incomplete commands are
discarded.
The ESMTP inspection engine changes the characters in the server SMTP banner to asterisks except for
the “2”, “0”, “0” characters. Carriage return (CR) and linefeed (LF) characters are ignored.
With SMTP inspection enabled, a Telnet session used for interactive SMTP may hang if the following
rules are not observed: SMTP commands must be at least four characters in length; must be terminated
with carriage return and line feed; and must wait for a response before issuing the next reply.
An SMTP server responds to client requests with numeric reply codes and optional human-readable
strings. SMTP application inspection controls and reduces the commands that the user can use as well
as the messages that the server returns. SMTP inspection performs three primary tasks:
•
Restricts SMTP requests to seven basic SMTP commands and eight extended commands.
•
Monitors the SMTP command-response sequence.
•
Generates an audit trail—Audit record 108002 is generated when invalid character embedded in
t
he
mail address is replaced. For more information, see RFC 821.
SMTP inspection monitors the command and response sequence for the following
anomalous signatures:
•
Truncated commands.
•
Incorrect command termination (not terminated with <CR><LR>).
•
The MAIL and RCPT commands specify who are the sender and the receiver of the mail. Mail
addresses are scanned for strange characters. The pipeline character (|) is deleted (changed to a blank
space) and “<” ‚”>” are only allowed if they are used to define a mail address (“>” must be preceded
by “<”). To close the session when the PIPE character is found as a parameter to a MAIL from or
RCPT to command, include the
special-character
command in the configuration as part of the
inspection parameters (
parameters
command).
•
Unexpected transition by the SMTP server.
•
For unknown commands, the ASA changes all the characters in the packet to X. In this case, the
server generates an error code to the client. Because of the change in the packed, the TCP checksum
has to be recalculated or adjusted.
•
TCP stream editing.
•
Command pipelining.
Summary of Contents for 5505 - ASA Firewall Edition Bundle
