Canon IR5000 - iR B/W Laser Service Manual Download

Page: 208 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 3 LASER EXPOSURE SYSTEM

3-9 P

4. Controlling the Laser Scanner Motor

4.1 Outline

The following signals are used to control the laser scanner motor:

[1] Laser scanner motor drive signal. When ‘1’, the laser scanner motor is turned on (i.e.,

turning on/off the motor).

[2] Laser scanner motor speed switch signal. When ‘0’, the motor is rotated at full speed;

when ‘1’, in-wait rotation (i.e., switching the speed).

[3] Laser scanner motor ready signal. When ‘0’, the laser scanner motor is rotated at a con-

stant speed (constant speed rotation control).

F03-401-01 Functional Block Diagram

E110

It is indicated under the following conditions:
[1] If the laser scanner motor ready signal (LMRDY*) goes ‘1’ when the

motor is rotating.

[2] If the laser scanner motor ready signal (LMRDY*) does not go ‘0’

within a specific period of time.

LMSPSEL [2]

J116

J2511 (J1)

+24V

GND

LMRDY

[3]

LMON [1]

Laser scanner
motor

DC controller
PCB

M15

Speed
control
circuit

Reference
pulse generation
circuit

Motor
driver

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands