Canon IR5000 - iR B/W Laser Service Manual Download Page 296

Page: 296 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 IMAGE FORMATION SYSTEM

4-83 P

7.11.5 Cleaning the Cleaner Side Scraper

Perform the following when replacing the cleaning blade (every 500,000 sheets).

1) Remove the cleaning blade.
2) Remove any paper lint collecting at the tip of the side scarper (A, i.e., between magnet

roller and toner guide roller) using tweezers or the like.

3) Remove the toner from the surface of the magnet roller. (Roll copy paper into a U to

scoop it up.)

F04-711-09

F04-711-10

4) Turn the magnet roller clockwise (viewing from the front).
5) Repeat steps 3) through 5) until the area from which toner was removed in step 3) is

once again coated with an even layer of toner.

4 to 8mm

Toner guide roller

Side scraper (front)

Remove waste toner

(front)

30 to 40mm

Toner guide roller

4 to 8mm

Side scraper (rear)

Magnet roller

Remove waste toner

(rear)

30 to 40mm

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands