Canon IR5000 - iR B/W Laser Service Manual Download Page 660

Page: 660 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-47 T

4.2.14 The drum heater fails to operate

General condition

1) Open the front cover, and release the fixing/feeding unit. Is the end

of the photosensitive drum warm? (Do not touch the surface of the
photosensitive drum.)

YES: The drum heater is normal.

Environment switch

2) Is the setting of the environment switch located at the left bottom of

the machine ‘ON” (powered at all times)?

NO:

Set it to ‘ON’. If set to ‘OFF’, it is linked to the main power
switch.

DC controller PCB, AC driver PCB

3) Set the meter range to 12 VDC. Connect the probes of the meter to

J102-B8 (+) and J102-B7 (-) on the DC controller PCB. Is the volt-
age between terminals about 2 V during copying and 0 V during
standby?

NO:

Replace the DC controller PCB.

Drum heater (H3)

4) Remove the drum, and set the meter range to

Ω

x1. Does the index

of the meter swing when the probes of the meter are connected to
both ends of the heater?

NO:

Replace the drum heater.

YES: Replace the heater control PCB.

4.2.15 The Add Toner message fails to turn on

General condition

1) Is there toner in the hopper?

YES: Go to step 2).

Hopper toner sensor (TS2), DC controller PCB

2) Replace the hopper toner sensor. Is the problem corrected?

NO:

Check the wiring; if normal, replace the DC controller PCB.

4.2.16 The Add Toner message fails to turn off

Toner (amount)

1) Is there toner in the hopper?

NO:

Supply toner. (Find out how the user is supplying toner.)

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands