Canon IR5000 - iR B/W Laser Service Manual Download | Manualshive

Page: 624 / 839

background image

COPYRIGHT © 2000 CANON INC.

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-11 T

3.10

The print has white spots (vertical)

3.11

The print has white lines (vertical)

Reader unit

1) Does the problem occur only in copy images?

YES: The cause is in the reader unit. Check the following:
1.

Standard white plate (back of copyboard glass) for dirt

2.

Execute the following in service mode:
COPIER>FUNCTION>CCD>CCD-ADJ.

3.

Execute the following in service mode:
COPIER>FUNCTION>CCD>SH-PS-ST.

Fixing assembly

2) Generate test print TYPE [00]. Turn off the main power switch immedi-
ately before the paper enters the fixing assembly, and check the image. Is it
normal?

YES: The cause is in a process after the fixing system. Check the follow-

ing:

1.

Fixing assembly upper roller for offset

Photosensitive drum

3) Are there scratches in the peripheral direction of the surface of the pho-
tosensitive drum that match the image?

YES: Find out the cause of the scratches, and replace the photosensitive

drum.

Developing assembly

4) Is the surface of the developing cylinder coated with an even layer of
toner?

NO:

Check the edge of the blade of the developing assembly for paper
lint or the like.

Transfer/Separation charging assembly, Pre-transfer charging assembly

5) Clean the pre-transfer charging assembly and the transfer/separation
charging assembly. Is the problem corrected?

YES: End.
NO:

Try changing the setting of the following in service mode:
COPIER>OPTION>BODY>FUZZY.

Download Free Service Manual at http://printer1.blogspot.com

«
...
622
623
624
625
626
...
»

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

Brand: Canon Pages: 840

Brand: Oce Pages: 18

Brand: Toshiba Pages: 127

C123 Copycentre

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands