Canon IR5000 - iR B/W Laser Service Manual Download

Page: 563 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

2-4 T

CHAPTER 2 IMAGE ADJUSTMENT BASIC PROCEDURE

4. Making Checks on the Reader Unit

Is there a difference

in density between

front and rear?

Are there vertical

lines in the images?

Clean the following:
1. Mirrors
2. Lens
3. Standard white plate
(mounted to back of
copyboard glass)

4. Copyboard glass

Clean the following:

1. Mirrors
2. Lens
3. Standard white plate
4. Scanning lamp
5. Reflecting plate

Make a copy of

the NA3 Chart in text mode. Is

gray scale No. 1 (solid black)

too light?

Check the life of the
scanning lamp; if it has
reached the end of its
life, replace it.

Making Image Initial Checks>

Checking the Solid Black Density

YES

End.

YES

Make one copy of the A3 Chart in
text/photo mode.

YES

Perform the instructions under

“ Checking the Density Slope”

for the printer unit.

Perform the instructions under

“ Checking the Solid Black Density”

for the printer unit.

YES

Go to “ Checking the Halftone Density” for the printer side.

Is there a

difference in density

between front

and rear?

Is the density of

gray scale No. 1 (solid black)

too low (light)?

Make a copy of

the NA3 Chart in text mode.

Is the white background

foggy?

Is the white
background

foggy?

Is the

density of gray scale

No.8 (halftone)

different?

If it is too dark,

If it is too light,

Perform the instructions
under “nChecking for
Fogging”g on the printer side.

YES

Make a copy of the

NA3 Chart in AE mode. Is the

output foggy?

Is the white
background

foggy?

Decrease the value of AE density
adjustment in service mode:
COPIER>ADJUST>AE>AE-TBL.

When

the A3 Chart

is copied in text/photo

mode, is the density of No.8 optimum

when compared with Nos.7

through 9?

Execute shading in service mode:
COPIER>FUNCTION>CCD>CCD-ADJ

Execute shading adjustment in service
mode:
COPIER>FUNCTION>CCD>CCD-ADJ.

Execute shading in service mode:
COPIER>FUNCTION>CCD>CCD-ADJ

Increase the white level target value for
shading correction in service mode:
COPIER>ADJUST>CCD>SH-TRGT
(40 max.).

Decrease the setting of the
following in service mode:
COPIER > ADJUST > DENS
>DENS-ADJ

Increase the setting of the
following in service mode:
COPIER > ADJUST > DENS
>DENS-ADJ

Executing Potential Control

Turn off and then on the power switch; then,
make a copy.

Clean the mirrors.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands