manualshive.com logo in svg

Canon IR5000 - iR B/W Laser, Service Manual

The Canon IR5000 - iR B/W Laser is a high-quality printing device designed to meet all your business needs. With its impressive speed and advanced features, this multifunctional printer ensures exceptional performance. Need guidance on operating it? Download the free service manual from manualshive.com to maximize the potential of this outstanding machine.

Share
Download
background image

COPYRIGHT © 2000 CANON INC. 

2000 2000 2000 2000

 CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 IMAGE FORMATION SYSTEM

4-14 P

2.5 APC Correction

The surface potential fluctuates in keeping with the increase/decrease in the laser output

caused by changes in laser temperature. To maintain the surface potential to a specific level,
the control value of the laser output is corrected.

The following shows the types of correction used for the laser output:

[1] Sheet-to-Sheet APC Control
Purpose: To maintain a specific level of surface potential without lowering productivity
when executing jobs in succession, the potential after laser output is measured between
sheets, ultimately correcting the control value of the laser output.
Timing: The control is executed during the first sheet-to-sheet interval each minute from the
start of continuous printing.
Potential measurement: The drum potential shows a discrepancy around the drum periphery
so that the average of potential levels is obtained. Based on the result, an appropriate correc-
tive value is obtained for the laser output. If measurement is not possible for some difficulty
(as in measuring between sheets), the attempt at measurement is continued for a further 1
min.

Potential
control for
copying

Potential
control for
printing

Main power
switch ON

Fixing assembly temperature
(end of fixing assembly warm-up)

Control panel power switch ON

Start key

ON

Correction of
laser output

1 min later

1 min later

Continuous printing

Correction of
laser output

F04-205-01

[2] Initial Rotation APC Control
Purpose: To make up for the change in VL potential in the laser output caused by changes in
temperature after a while, the surface potential of the drum is measured, and the control
value of the laser output is corrected.
Timing: The control is executed during initial rotation for the first job 60 min after the end
of jobs.
Potential measurement: The drum potential shows a discrepancy around the drum periphery
so that the average of potential levels is obtained. Based on the result, an appropriate correc-
tive value is obtained for the laser output.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

Xerox DOCUCOLOR 12 System Administration Manual preview
DOCUCOLOR 12
Brand: Xerox Pages: 110
Olivetti AR-NC7 Service Manual preview
AR-NC7
Brand: Olivetti Pages: 22
Olivetti d-Copia 4003MF Service Manual preview
d-Copia 4003MF
Brand: Olivetti Pages: 487
Minolta EP3050 Operator'S Manual preview
EP3050
Brand: Minolta Pages: 206

Brands by name

Popular brands

Load more brands