Canon IR5000 - iR B/W Laser Service Manual Download

Page: 662 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-49 T

Cassette pickup assembly

2) Is the lifter mechanism of the cassette normal?

NO:

Replace the lifter unit or the cassette pickup assembly.

4.2.21 The fixing heater fails turn on

Fixing/feeding lock sensor (MSW3)

1) Is the fixing/feeding lock sensor mounted correctly?

NO:

Mount the fixing/feeding lock sensor correctly.

YES: Replace the sensor.

Thermal switch (TP1)

2) Connect the probes of the meter to both terminals of the thermal

switch. Is there electrical continuity?

NO:

Replace the thermal switch.

Main relay (RL1)

3) Try replacing the main relay. Is the problem corrected?

YES: End.

Fixing heater (H1, H2)

4) Connect the probes of the meter to both terminals of the fixing

heater. Is there electrical continuity?

NO:

Replace the fixing heater.

AC driver PCB, DC controller PCB

5) Is the voltage between the following connectors on the DC control-

ler PCB about 5 V?

Heater

Main heater (H1)

J102-B11

J102-B7

Sub heater (H2)

J102-B9

J102-B7

YES: Replace the AC driver PCB.
NO:

Replace the DC controller PCB.

4.2.22 Pickup fails (paper deck)

Right upper cover, Right lower cover

1) Are the right upper cover and the right lower cover closed prop-

erly?

NO:

Close the covers.

Lifter

2) Slide out the compartment from the deck. Does the lifter move

down? Further, does the lifter move up when the compartment is
slid inside the deck?

NO:

See “The deck lifter fails to move up.”

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands