Canon IR5000 - iR B/W Laser Service Manual Download | Manualshive

Page: 633 / 839

background image

COPYRIGHT © 2000 CANON INC.

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-20 T

4. Troubleshooting Malfunctions

4.1 Troubleshooting by Malfunction

4.1.1 E000

Thermistor (TH1, TH2)

1) Clear E000, and turn off and then on the main power switch. Make

the following selections in service mode:
COPIER>DISPLAY>ANALOG. Does <FIX-U> show an increase in
temperature?

YES: The thermistor is faulty. Check the following:

•

thermistor for mounting condition

•

thermistor for soiled surface

•

connection

Fixing heater (H1, H2; open circuit)

2) Is the electrical continuity of the fixing upper heater normal?

NO:

Replace the fixing heater.

DC controller PCB, AC driver PCB (faulty)

3) Turn off the main power switch, and let the fixing upper roller cool.

Then, turn on the main power switch. Clear E000, and trun off and
then on the main power switch. Make the following in service
mode: COPIER>I/O>DC-CON. Are bit 4 and bit 5 of IO-P12 ‘0’?

YES: Check the wiring; if normal, replace the DC controller PCB.
NO:

Check the wiring; if normal, replace the AC driver PCB.

4.1.2 E001

AC driver PCB (fixing heater drive circuit; short circuit)

1) While keeping the main power switch off, let the fixing upper roller

cool. While at it, check each thermistor for a soiled surface, poor
mounting, and poor connection.
Turn on the main power switch, and clear E001; then, turn off and
then on the power switch. Make the following selections in service
mode: COPIER>DISPLAY>ANALOG. Is <FIX-U> about 230°C or
higher?

YES: Replace the AC driver PCB.

Thermistor (TH1, TH2), DC controller PCB

2) Try replacing the thermistor. Is the problem corrected?

YES: End.
NO:

Check the wiring; if normal, replace the DC controller PCB.

Download Free Service Manual at http://printer1.blogspot.com

«
...
631
632
633
634
635
...
»

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

imageCLASS MF3010

Brand: Canon Pages: 2

imageCLASS 1100

Brand: Canon Pages: 260

Brand: Canon Pages: 458

CyberScanner Basic

Brand: Easypix Pages: 27

Cyber Scanner Basic

Brand: Easypix Pages: 31

Document Centre 240

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands