Canon IR5000 - iR B/W Laser Service Manual Download Page 667

Page: 667 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-54 T

Transfer/Separation charging assembly

6) Is the transfer/separation charging assembly mounted securely?

YES: Check the transfer/separation charging assembly.

7) Are there burrs on the paper guide of the transfer/separation

charging assembly?

YES: Remove the burrs.

8) Is there foreign matter on the transfer/separation charging assem-

bly?

YES: Remove the foreign matter.

Print paper

9) Try paper of a recommended type. Is the problem corrected?

YES: Advise the user to use recommended paper.

Separation claws (cleaning assembly)

10) Are the separation claws under the cleaning assembly damaged?

YES: Replace the separation claws.

11) Is the spring of the separation claw displaced?

YES: Mount the spring correctly.

Feeding belt

12) Are the three feeding belts rotating correctly?

YES: Check to see if the feeding fan is operating.

Feeding fan

YES: Check to make sure that the feeding fan is operating.

5.1.3 Fixing/Delivery assembly

Separation claws (delivery assembly)

1) Are the separation claws worn/deformed?

YES:
1.

Replace the separation claws.

If dirt is found, clean them with solvent.

Upper/lower roller (fixing assembly)

2) Is the upper/lower roller of the fixing assembly worn or scratched?

YES: Replace the roller.

Paper guide (fixing assembly)

3) Is the paper guide soiled with toner?

YES: Clean it with solvent.

4) Is the height of the paper guide normal?

NO:

Adjust it.

5) Is the inlet guide switched over to suit the passage of small-size pa-

per and large-size paper?

NO:

Check the fixing assembly inlet guide drive solenoid (SL1).

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Brands by name

Popular brands