Canon IR5000 - iR B/W Laser Service Manual Download

Page: 663 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 4 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

4-50 T

Deck pickup roller

3) Does the deck pickup roller rotate?

YES: If the roller is soiled, clean it with alcohol. If it is deformed be-

cause of wear, replace it.

Belt (displacement)

4) Is the belt used to transmit drive to the deck pickup roller attached

correctly?

NO:

Attach the belt correctly.

Gear

5) Is the drive from the deck main motor transmitted through the

gear?

NO:

Check the gear.

Deck pickup clutch (CL102), Deck driver PCB

6) Measure the voltage of the connector on the deck driver PCB. Does

the voltage change from 24 to 0 V when the Start key is pressed?

Clutch

Deck pickup clutch

J05-11

J05-12

YES: Check the wiring; if normal, replace the clutch.
NO:

Replace the deck driver PCB.

4.2.23 The deck lifter fails to move up (side paper deck)

Deck

1) Is the deck mounted correctly?

NO:

Mount the deck correctly.

Lifter cable

2) Is the lifter cable routed correctly?

NO:

Route the lifter cable correctly.

Spring, Lever

3) Push up the deck pickup roller releasing lever with your finger.

Does the roller move down?

NO:

Remove the pickup assembly, and check the spring and the lever.

Deck lifter motor (M102)

4) Does the deck lifter motor rotate?

YES: Go to step 6).

Deck open detecting switch (SW101), Deck driver PCB

5) Does the voltage between J10-1 (+) and J10-3 (GND) on the deck

driver PCB change from about 0 to 5 V when the deck is closed?

YES: Check the wiring to the switch; if normal, replace the switch.
NO:

Replace the deck driver PCB.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands