Canon IR5000 - iR B/W Laser Service Manual Download | Manualshive

Page: 118 / 839

background image

COPYRIGHT © 2000 CANON INC.

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 2 ORIGINAL EXPOSURE SYSTEM

2-12 R

F02-404-01

Point of original detection

Copyboard glass

Xenon lamp

Original sensor

Reader unit

Copyboard cover

Point of original detection 1
Point of original detection 2
Point of original detection 3
Point of original detection 4

(external light)

Original (A4R)

(external light)

4.4 Outline of Detection Operation

4.4.1 Book Mode, 1 Original, Copyboard Cover Open

[1] The scanner remains in wait.

No. 1 mirror base: at HP
Xenon lamp: off
Original sensor: disabled

[2] The copyboard is opened.

Detection starts of external light in main
scanning direction.
No. 1 mirror base: to point of original de-
tection
Xenon lamp: off
Original sensor: disabled

[3] An original is placed.

The width of the original is identified in
relation to the presence/absence of external
light; here, the absence of an original is
identified at points in question, eliminating
B5, B4, A4, and A3.

[4] The Start key is pressed.

In response, original detection is started.
For main scanning direction, the xenon
lamp is turned on to check for reflected
light by the CCD (4 points).
For sub scanning direction, the original
sensor starts detection.
The absence of external light is identified
as indicating the absence of an original.
The machine will identify the size of an
original based on the combination of the
results (T02-404-01)

Download Free Service Manual at http://printer1.blogspot.com

«
...
116
117
118
119
120
...
»

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

Brand: Olivetti Pages: 36

Brand: Minolta Pages: 167

Brand: Xerox Pages: 105

Copycentre C118

Brand: Xerox Pages: 47

C123 Copycentre

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands