Canon IR5000 - iR B/W Laser Service Manual Download

Page: 609 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 3 STANDARDS AND ADJUSTMENTS

3-44 T

Printer Unit (service mode: COPIER>I/O>DC-CON)

Sensor

Connector No.

Checks

I/O

Voltage

I/O address

display display

PS2

D>J113-A14

Open and close the right lower cover. Cover

Open

Right lower cover open/closed sensor ---

Closed

PS3

D>J103-B14

Open and close the manual feed tray. Tray

Open

Manual feed tray open/closed sensor IO-P03-13

Closed

PS4

D>J106-B19

Put paper over the point of detection. Paper

Present

Claw jam sensor

IO-P01-14

Absent

PS5

D>J112-B2

Open and close the right deck.

Right deck Open

Right deck open/closed sensor IO-P03-11

Closed

PS6

D>J112-A2

Put paper in the right deck.

Paper

Present

Right deck lifter sensor

IO-P03-1

Absent

PS7

D>J112-A5

Put paper in the right deck.

Paper

Present

Right deck paper sensor

IO-P01-7

Absent

PS8

D>J112-B8

Put paper in the right deck.

Paper

Present

Right deck limit sensor

IO-P02-4

Absent

PS9

D>J115-A14

Open and close the left deck.

Left deck Open

Left deck open/closes sensor

IO-P03-12

Closed

PS10

D>J115-A5

Put paper in the left deck.

Paper

Present

Left deck lifter sensor

IO-P03-3

Absent

PS11

D>J115-A8

Put paper in the left deck.

Paper

Present

Left deck paper sensor

IO-P01-9

Absent

PS12

D>J115-A2

Put paper in the left deck.

Paper

Present

Left deck limit sensor

IO-P03-4

Absent

PS13

D>J110-A5

Put paper in the cassette 3.

Paper

Present

Cassette 3 paper sensor

IO-P01-3

Absent

PS14

D>J110-B5

Put paper in the cassette 4.

Paper

Present

Cassette 4 paper sensor

IO-P01-5

Absent

PS15

D>J110-A11

Open and close the cassette 3.

Cassette

Open

Cassette 3 open/closed sensor IO-P04-3

Closed

PS16

D>J110-B11

Open and close the cassette 4.

Cassette

Open

Cassette 4 open/closed sensor IO-P04-4

Closed

PS17

D>J110-A2

Put paper in the cassette 3.

Paper

Present

Cassette 3 lifter sensor

IO-P03-5

Absent

PS18

D>J110-B2

Put paper in the cassette 4.

Paper

Present

Cassette 4 lifter sensor

IO-P03-6

Absent

PS19

D>J112-A8

Put paper over the point of

Paper

Present

Right deck re-tray sensor

IO-P01-2

detection.

Absent

T03-1003-02

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands