Canon IR5000 - iR B/W Laser Service Manual Download

Page: 440 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 7 EXTERNALS AND CONTROLS

7-15 P

[1]

[3]

[2]

[5]

[4]

5.1.2 Removing the Front Cover

1) Open the front cover [1], and remove

the screw [3] of the door tape [2].

2) Remove the stopper [4], and detach the

hinge shaft [5] by pulling it up.

3) Pull the front door up at an angle to de-

tach.

F07-501-03

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands