manualshive.com logo in svg

Canon IR5000 - iR B/W Laser, Service Manual

Share
Download
Canon IR5000 - iR B/W Laser Service Manual Download Page 114

COPYRIGHT © 2000 CANON INC. 

2000 2000 2000 2000

 CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 2 ORIGINAL EXPOSURE SYSTEM

2-8 R

Vertical size plate

Standard white plate

Increase

Decrease

Copyboard glass

Vertical size plate

Standard white plate

Increase

Decrease

Copyboard glass

HP sensor

F02-204-02

2.2.2 Reversing the Scanner After Scanning in Main Reading Direction

When the image has been scanned, the No. 1 mirror base is moved in reverse to home po-

sition at the speed used for 50% reduction, regardless of the ratio being used.

E202 (HP detection error)

[1] The No. 1 mirror base does not reach the HP sensor within a specific

period of time.

[2] The HP sensor identifies the presence of the No. 1 mirror base when the

No. 1 mirror base should have been moved away.

E204 (image leading edge detection error)

[1] The image signal is not generated when the No. 1 mirror base is moving

forward.

[2] The ADF does not generate the image leading edge signal in stream

reading mode.

COPIER>ADJUST>ADJ-XY>ADJ-X (scanner image leading edge
adjustment)

Enter an appropriate value to adjust the image leading edge position.
Range: 0 through 2970 (a change of ‘12’ causes a shift of 1 mm)

COPIER>ADJUST>ADJ>XY>ADJ-S (scanner home position adjust-
ment)

Enter an appropriate value to adjust the home position (standard white plate
read position).
If the standard white plate is soiled, execute this mode so that the plate is
read avoiding the soiled area.
Range: 0 to 4

F02-204-01

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands