manualshive.com logo in svg

Canon IR5000 - iR B/W Laser, Service Manual

Share
Download
Canon IR5000 - iR B/W Laser Service Manual Download Page 745

COPYRIGHT © 2000 CANON INC. 

2000 2000 2000 2000

 CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 5 SERVICE MODE

5-52 T

COPIER>ADJUST

<HV-PR1>

Adjusting the Output of the Primary Charging Assembly
If you have cleared the RAM on the DC controller PCB, enter the settings indicated on

the service label.

PRIMARY

Use it to enter the adjustment value of the primary current for non-potential
control.

Range of

0 to 1400

adjustment

<HV-TR>

Adjusting the Output of the Transfer Charging Assembly/Pre-Transfer Charging Assem-

bly

TR-N1

Use it to enter the output adjustment value for the transfer charging current
(for printing on the face of plain paper and printing on the 1st side of a
double-sided sheet).

Caution

If you have cleared the RAM on the DC controller PCB, enter the settings

indicated on the service label.

TR-N2

Use it to enter the output adjustment value for the transfer charging current
(printing on the 2nd side of a double-sided plain paper sheet).

Caution

If you have cleared the RAM on the DC controller PCB, enter the settings

indicated on the service label.

PRE-TR

Use it to enter the output adjustment value for the pre-transfer charging cur-
rent.

Caution

If you have cleared the RAM on the DC controller PCB, enter the settings

indicated on the service label.

HVT-TR

Enter the offset value for the transfer high-voltage output of the high-volt-
age unit.

Caution

If you have replaced the high-voltage unit or cleared the RAM on the DC

controller PCB, enter the settings indicated on the label attached to the new
high-voltage unit.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands