Canon IR5000 - iR B/W Laser Service Manual Download

Page: 808 / 839

2000 2000 2000 2000

CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 6 SELF DIAGNOSIS

6-11 T

E740

Main cause

The LAN card is faulty. The main controller PCB is faulty.

Mode of
Detection

0001 An error is detected on the LAN card at power-on (with the card

inserted).

0002 A MAC address is found to be faulty.
0003 The LAN card register cannot be read.

E741

Main Cause

The PCI bus connection is not proper. The main controller PCB is faulty.

Mode of
Detection

0000 An error has occurred in the PCI bus.

E742

Main Cause

The RIP1 board (accessory) is faulty. The main controller PCB is faulty.

Mode of
Detection

0000 An error has been detected by self diagnosis of the RIPI board.

E743

Main cause

The connector has poor contact. The main controller PCB is faulty.

Mode of
Detection

0000 The reader controller PCB has detected an error in the communica-

tion between the main controller PCB and the reader controller
PCB.

E804

Main Cause

The wiring is faulty (short circuit, open circuit). The DC power supply fan
(FM6) is faulty. The DC controller PCB is faulty.

Mode of
Detection

0000 While the DC power supply fan is being driven, the clock signal

(FM6CLK) does not arrive for 5 secs or more.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser
















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands

Canon IR5000 - iR B/W Laser, Service Manual

Search results

Summary of Contents for IR5000 - iR B/W Laser

Reviews:

Related manuals for IR5000 - iR B/W Laser

Brands by name

Popular brands