manualshive.com logo in svg

Canon IR5000 - iR B/W Laser, Service Manual

The Canon IR5000 - iR B/W Laser is a high-quality printing device designed to meet all your business needs. With its impressive speed and advanced features, this multifunctional printer ensures exceptional performance. Need guidance on operating it? Download the free service manual from manualshive.com to maximize the potential of this outstanding machine.

Share
Download
background image

COPYRIGHT © 2000 CANON INC. 

2000 2000 2000 2000

 CANON iR5000/iR6000 REV.0 JULY 2000

CHAPTER 2 ORIGINAL EXPOSURE SYSTEM

2-11 R

Point of original 
detection 3
Point of original 
detection 4

Point of original 
detection 1

Point of original 
detection 2

B5

A4

B5R

A4R

B4

A3

Point of CCD original detection

Point of CCD original detection

Point of original 
detection 1

Point of original 
detection 2

LTRR

LTR

LGL

279.4×431.8mm
(11"×17")

Original sensor

Original sensor

AB-Configuration

Inch-Configuration

F02-402-01

4.3 Outline of Detection

The machine identifies the size of originals in the following two steps:

[1] Detecting External Light (main scanning direction only)

While keeping the scanning lamp off, the CCD level at each point of detection in main
scanning direction is measured. A point at which external light is detected will be iden-
tified as indicating the absence of an original, enabling the identification of the width
of an original.

[2] Detecting the Sensor Output Level

The scanning lamp is turned on, and the CCD level at each point of detection in main
scanning direction is measured. In addition, the reflection type photosensor in sub
scanning direction is turned on to measure the sensor output.
The combination of these output measurements is used to identify the size of the origi-
nal. For specific movements, see the pages that follow.

4. Detecting the Size of Originals

4.1 Outline

The machine automatically identifies the size of originals based on the combination of in-

tensities measured by reflection type sensors and CCD at specific points.

•

For main scanning direction, the CCD is used to take measurements (if AB, 4 points; if
Inch, 2 points).

•

For sub scanning direction, a reflection type photosensor is used (1 point).

4.2 Points of Detection

For main scanning direction, the No. 1 mirror base is moved to the following points in re-

lation to the position of the original to measure the intensity at each point.

For sub scanning direction, on the other hand, measurements are taken while holding the

sensor in place at a specific point.

Download Free Service Manual at http://printer1.blogspot.com

Summary of Contents for IR5000 - iR B/W Laser








































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IR5000 - iR B/W Laser

Canon IMAGERUNNER 2016 Media Manual preview
IMAGERUNNER 2016
Brand: Canon Pages: 2
Canon IMAGERUNNER 2022i Specifications preview
IMAGERUNNER 2022i
Brand: Canon Pages: 4
Avision ScanCopier Service Manual preview
ScanCopier
Brand: Avision Pages: 51
Avision DS310F User Manual preview
DS310F
Brand: Avision Pages: 65
RealSYS SmartCopier User Manual preview
SmartCopier
Brand: RealSYS Pages: 23

Brands by name

Popular brands

Load more brands