Canon iR C3380 series, Service Manual

Page: 536 / 610

Chapter 17
17-52
ORG-LGL Use it to set a special paper size not recognized by the DF size detection mechanism.
settings
0: LEGAL
1: FOOLSCAP
2: A-FOOLSCAP
3: FORIO
4: G-LEGAL
5: OFFICIO
6: E-OFFICIO
7: A-OFFICIO
8: B-OFFICIO
9: A-LEAGAL
10: M-OFFICIO
[Factory default/After RAM clear: 0]
2
ORG-LTR Used to set special paper size not compatible with DF size recognition.
Setting values
0: LTR
1: G-LTR
2: A-LTR
3: EXECTIVE
[Factory settings and after RAM clear: 0]
2
ORG-B5 Sets special paper sizes that cannot be detected in ADF.
Setting values
0: B5
1: K-LEGAL
[Factory settings and after RAM clear: 0]
2
UI-COPY Use it to select whether to display the copy screen in the control panel.
Setting values
0: Do not display the copy screen.
1: Display the copy screen.
[Factory default/After RAM clear: 1]
2
UI-BOX Used to select whether to display operation panel box screen.
Setting values
0: Don't display
1: Display
[Factory default/After RAM clear: 1]
2
UI-SEND Used to select whether to display operation panel send screen.
Setting values
0: Don't display
1: Display
[Factory default/After RAM clear: 1]
2
UI-FAX Used to select whether to display operation panel fax screen.
Setting values
0: Don't display
1: Display
[Factory default/After RAM clear: 1]
2
SCR-SLCT Used to select half-tone process for photographic printing paper/photo mode.
Setting values
0: Use error diffusion method
1: Use low-line-count screen
2: Use high-line-count screen
[Factory default/After RAM clear: 1]
2
TMC-SLCT Used to select coefficient used in error diffusion process.
Setting values
0: Low granularity/low dot stability for Y/M/C/Bk
1: Y/M/C -> Low granularity, low dot stability, Bk -> high granularity, low dot stability
2: High granularity/low dot stability for Y/M/C/Bk
[Factory default/After RAM clear: 1]
2
DEVL-VTH Sets threshold value (video count) for starting toner forcible consumption sequence.
Whenever possible, avoid using this setting during normal operation.
2
FTPTXPN Used to specify port (FTP) number to send to.
0 to 65535 (16-bit value)
[Factory default/After RAM clear: 21]
2
PRNT-ORD Used to switch order of output to side tray.
Whenever possible, avoid using this setting during normal operation.
2
PRN-FLG Used to select area flag for PDL images.
Whenever possible, avoid using this setting during normal operation.
2
SCN-FLG Used to select area flag for copy images.
Whenever possible, avoid using this setting during normal operation.
2
T-LW-LVL Low remaining toner warning message display timing selection
This selects the threshold (%) of the remaining amount of toner at which "Low toner message" is displayed on the control
unit. It is used when selecting the percentage of the toner left at which to display the supply toner warning.
Settings
0: Normal level (5% remaining)
1: 10% remaining
2: 15% remaining
3: 20% remaining
[Factory setting/value after clearing RAM: 0]
Attention:
Every effort must be made to avoid using this when the machine is operating normally.
2
NWERR-SW Used to select whether to display network error messages.
Setting values
0: Don't display
1: Display
[Factory default/After RAM clear: 1]
2
COPIER>OPTION>BODY