Chapter 9
9-13
F-9-16
9) From the fixing film unit [1], slide the 2 leaf springs [2] in the direction of
the arrow, and remove them; then, remove the separation guide [3].
F-9-17
Points to Note when Attaching the Shutter Unit
When attaching the shutter unit [1], it could damage the fixing film. There-
fore, be sure to go through the following procedure.
1) Cover the fixing film with the protection sheet [2].
F-9-18
2) Fit the shutter unit [1] onto the positioning pin [2].
F-9-19
3) Tighten the 5 screws [1], and pull out the protection sheet [2].
F-9-20
9.5.3 Pressure Roller
9.5.3.1 Before Removing Pressure Rolle
0013-8776
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1) Remove the fixing film unit.
(page 9-12)
[Removing Fixing Film Unit]
9.5.3.2 Removing Pressure Roller
0013-8777
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1) Remove the screw [1]; then, remove the inlet guide [2] by sliding in the
direction of the arrow.
F-9-21
2) Open the jam removal door [1], and inset the screwdriver [2] as indicated
in the following figure.
F-9-22
3) By lifting one side of the pressure roller [1], remove the bush [2] and
bearing [3].
[4]
[1]
[2]
[3]
[5]
[3]
[2]
[2]
[1]
[2]
[1]
[1]
[2]
[2]
[1]
[1]
[2]
[1]
[2]
Summary of Contents for iR C3380 series
