manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 93 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 93

10.3  LED Indicator

Mode

Run

FWD

REV

Power off

Off

Off

Off

Ready

Off

Green / Off

Off / Green

Run (FWD)

Green

Green

Off

Run (REV)

Green

Off

Green

Run pending

Blinks in green
(Short green
long dark)

Green / Off

Off / Green

DC-braking at start
Direction change dead time
Deceleration stop phase

Blinks in green
(Short dark
long green)

Green / Off

Off / Green

DC-braking at stop

Warning with FWD

Green

Green

Off

Warning with REV

Green

Off

Green

Warning at stop

Off

Green / Off

Off / Green

Error

Off

Green / Off

Off / Green

Tab.  10-1:   LED indicator status

The frequency converter stops if FWD and REV commands are active

at the same time.

VFC 3210 

Bosch Rexroth AG

Operating Panel and Dust Cover

DOK-RCON04-VFC3210****-IT01-EN-P

65/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments