manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 209 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 209

13.4.19  Error 31 (Ot): Motor over Temperature

Possible reason

Solution

Excessive load or bad cooling

● Check load
● Provide a better cooling condition

Temperature sensor defect

Check the motor temperature sensor feedback signal

Wrong motor protection parameter set-

tings

Different  motor  with  different  maximum  temperature,  set

motor protection parameters according to actual protection

circuits (C1.72, C1.73, C1.74)

13.4.20  Error 32 (t-Er): Motor Parameter Tuning Error

Possible reason

Solution

Motor  power  and  frequency  converter

power do not match

Motor power has to match with frequency converter power

Wrong setting of motor parameters

Correct motor parameters setting according to motor name-

plate

No connection of converter and motor

Check motor cable connections

13.4.21  Error 38 (AibE): Analog Input Broken Wire Detection

Possible reason

Solution

Analog input wire is disconnected

Check wiring of AI1, AI2 and EAI

13.4.22  Error 39 (EPS-): DC_IN Power Supply Error

Possible reason

Solution

DC_IN  power  supply  voltage  is  out  of

range 20...28 V

Check the voltage supply on DC_IN terminal and make sure

the voltage is within the range of 20...28 V

13.4.23  Error 40 (dir1): Forward Running Lock Error

Possible reason

Solution

Direction control [E0.17] = '1: Forward

only'
Direction command is reverse

Correct the parameter setting

VFC 3210 

Bosch Rexroth AG

Diagnosis

DOK-RCON04-VFC3210****-IT01-EN-P

181/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments