manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 244 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 244

16.2  Daily Inspection

Please conduct daily inspection as indicated in the table below in order to pro-

long the life cycle of frequency converters.

Inspection

category

Inspection item

Inspection criteria

Inspection

result

Ambient
conditions

Temperature

-10...55 ℃ (no frost or condensation)

 

Relative humidity

≤ 90 % (no condensation)

 

Dust, water
and leakage

No heavy dust or sign of leakage
(visual inspection)

 

Gas

No harmful, flammable gas or strange smell

 

Sound

No strange sound

 

Panel display

No error code

 

Others

No direct sunlight, no oil or corrosive substan-

ces around

 

Converter

Status

Running stably, the outlet temperature is nor-

mal

 

Fan

No blockage or contamination

 

Terminal, screw

Wiring  is  correct,  screw  fastening  without

loosening

 

Motor

Sound, vibration

No strange sound, no abnormal vibration

 

Temperature, color

No abnormal temperature and discoloration

 

Tab.  16-1:   Daily inspection list

Bosch Rexroth AG
Maintenance

 VFC 3210

216/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments