Home
/
Bosch
/
Rexroth VFC 3210
/
Operating Instructions Manual

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 116 / 282

Share

Page: 116 / 282

Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 116

12.3.2 Fan Maintenance Reminder

This function is used to remind users maintaining the cooling fan in time. The

maintenance time can be set according to the actual application conditions.

Code

Name

Setting range

Default

Min.

Attri.

C0.51 Fan total running time

0...65,535 h

0

1

Read

C0.52 Fan maintenance time

0...65,535 h

0

1

Stop

C0.53 Fan total running time reset

0: Inactive
1: Active

0

–

Run

To use this function, take the following steps:
Step 1: Set the maintenance time of the fan properly
Set parameter C0.52 'Fan maintenance time' according to the actual application

conditions.

Step 2: Observe the fan lifetime status at warning
When a warning code 'FLE' (Fan maintenance period expired) is displayed on the

operating panel, [C0.51] 'Fan total running time' is higher than [C0.52] 'Fan

maintenance time'.

●

Pause the display of the warning code 'FLE' by pressing the <Func> button.

●

Perform fan maintenance or replacement.

Step 3: Reset the fan lifetime counter after fan maintenance or replacement

●

Set parameter C0.53 'Fan total running time reset' to '1: Active'
After the execution, [C0.53] and [C0.51] will be reset to '0' automatically. By

now, the warning code 'FLE' is cleared completely.

●

Adjust the value of C0.52 'Fan maintenance time' if necessary

Bosch Rexroth AG
Functions and Parameters

VFC 3210

88/253

DOK-RCON04-VFC3210****-IT01-EN-P

«
...
114
115
116
117
118
...
»

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments