manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 262 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 262

C2: V/f control parameters

Code

Name

Setting range

Default

Min.

Attri.

C2.00 V/f curve mode

0: Linear
1: Square
2: User-defined

0

–

Stop

C2.01 V/f frequency 1

0.00...[C2.03] Hz

0.00

0.01

Stop

C2.02 V/f voltage 1

①

0.0...120.0 %

0.0

0.1

Stop

C2.03 V/f frequency 2

[C2.01]...[C2.05] Hz

0.00

0.01

Stop

C2.04 V/f voltage 2

①

0.0...120.0 %

0.0

0.1

Stop

C2.05 V/f frequency 3

[C2.03]...[E0.08] Hz

50.00

0.01

Stop

C2.06 V/f voltage 3

①

0.0...120.0 %

100.0

0.1

Stop

C2.07 Slip compensation factor

0…200 %

0

1

Run

C2.20 0 Hz output mode

0: No output
1: Standard

1

1

Stop

C2.21 Torque boost setting

0.0 %: Automatic boost
0.1...20.0 %: Manual boost

DOM

0.1

Run

C2.22 Automatic torque boost factor 0...320 %

50

1

Run

C2.23

Heavy load stabilization
setting

0: Inactive
1: Active

1

–

Run

C2.24

Light load oscillation damping
factor

0...5,000 %

0

1

Run

C2.25

Light load oscillation damping
filter factor

10...2,000 %

100

1

Run

C2.40 Current limitation mode

0: Always inactive
1: Inactive at constant speed
2: Active at constant speed

2

–

Stop

C2.42 Current limitation level

②

[C0.27]...250 %

150

1

Stop

C2.43 Current limitation proportional

gain

0.000...10.000

DOM

0.001

Stop

C2.44

Current limitation
integral time

0.001...10.000

DOM

0.001

Stop

①

: percentage of motor rated voltage [C1.06].

②

: percentage of frequency converter rated current.

Bosch Rexroth AG
Appendix

 VFC 3210

234/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments