Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 172

Page: 172 / 282

12.9.6 PID Deactivation by Digital Input

Fig. 12-39: PID deactivation by digital input

The PID control is deactivated in the following ways:

●

'PID reference channel' [E4.00] = '0: No PID control' or

●

[E1.00]...[E1.04] / [H8.00]...[H8.03] = '41: PID deactivation' and respective

multi-function digital input terminal is active.

12.9.7 PID Engineering Value Display

This function is used to display an engineering value which is convenient for the

application engineering with scaling the output value, follow the equations be-

low:

●

User-defined setting speed:
[d0.04] = [d0.02] x [E5.02]

●

User-defined actual speed:
[d0.05] = [d0.00] x [E5.02]

Code

Name

Setting range

Default

Min.

Attri.

E5.02 User-defined speed scaling factor

0.01...100.00

1.00

0.01

Run

d0.01 Actual speed

–

1 rpm Read

d0.03 Setting speed

–

1 rpm Read

d0.04 User-defined setting speed

–

0.1

Read

d0.05 User-defined output speed

–

0.1

Read

d0.70 PID reference engineering value

–

0.1

Read

d0.71 PID feedback engineering value

–

0.1

Read

[d0.70] = [E4.02] x [PID reference]
[d0.71] = [E4.02] x [PID feedback]

Bosch Rexroth AG
Functions and Parameters

VFC 3210

144/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Search results

Summary of Contents for Rexroth VFC 3210

Reviews:

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 172 / 282

Search results

Summary of Contents for Rexroth VFC 3210

Reviews: