manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 211 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 211

13.4.28  Error 45 (E.Par): Parameter Settings Invalid

Possible reason

Solution

Parameter settings are invalid after firmware update or

extension card removed or parameter copy

1. Check  parameter  group  '-EP-'  and

modify the parameter values appeared

in '-EP-'

2. Initialize all parameters

13.4.29  Error 48 (idA-): Internal Communication Error

Possible reason

Solution

Internal error caused by communication between con-

trol boards

Contact with service

13.4.30  Error 49 (idP-): Internal Parameter Error

Possible reason

Solution

Internal error caused by parameter handling

Contact with service

13.4.31  Error 50 (idE-): Converter Internal Error

Possible reason

Solution

Internal error occurs

Contact with service

13.4.32  Error 56 (PrEF): Parameter Restore Error after Firmware Update

Possible reason

Solution

Error  occurs  if  parameter  settings  cannot  be  restored

after firmware update

Contact with service

VFC 3210 

Bosch Rexroth AG

Diagnosis

DOK-RCON04-VFC3210****-IT01-EN-P

183/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments