BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 97

Page: 97 / 183

Maintenance

Manual No. 188000
September 1, 2009

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and Parts

List

5-53

Assembly of Power Unit

(Continued)

Step 5: Install Muffler

Slide the muffler into the power unit.

Step 6: Install Retainer



Screw the retainer firmly into the power unit, using the supplied spanner wrench. The
retainer is a left-hand thread, and must be turned to the left (counter clockwise), to
tighten.

NOTE:

Recommended torque of 25-30 lb-in

(2.8-3.4 N-m)

IMPORTANT:

Be careful not to cross thread the retainer.

This will cause poor motor

performance.

Muffler

Installed

Retainer

Spanner
Wrench

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands