manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 85

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-41 

 

Assembly of TRIMVAC

®

 AMX Handpiece

 (Continued) 

 

Step 7:  Install Blade (Continued): 

 

 

Carefully insert the blade. 

 
 
 
 
 
 
 
 
 
 
 
 

 

Loosen the left cover retaining screw so the housing will close. 

 

NOTE:  

Be certain that the blade is free to move in the housing.  If the blade does not move freely, it 

may cause the trimmer to overheat. 

 

 

TRIMVAC

®

 45AMX: 

 

 

Adjust the housing for proper running clearance. 

 

If the blade is tight in the housing, adjustments can 
be made by loosening the left cover retaining screw 
and slightly spreading open the housing.  Check for 
free movement. 

 

Retighten the cover retaining screws. 

 

NOTE:  

Recommended torque of 30-40 lb-in (3.4-4.5 N-m) 

 

 

 

 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands