manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 27

 Instructions for Operation 

 

 

Manual No.  188000  
September 1, 2009 

 Instructions for Operation  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

4-3 

 

Power Unit / Head Assembly - Attachment and Adjustment 

 

The Whizard

® 

AirMax MACH 3 Trimmers have been designed to allow the head of the tool to 

be rotated relative to the handle.  In this way, the tool can be adjusted to align the blade with the 
product, while maintaining a comfortable position for the operator’s wrist. 
 
The position that is selected should be based on the individual workstation, product, and 
operator.  To determine the proper position, it will be necessary to observe the operator while 
trying various positions.  Select the position which is most comfortable to the operator. 
 
Note that left-handed tools are available for left-handed users.  Do not assign a right-handed tool 
to a left-handed user.  

 

 
 

 

 

W A R N I N G  

 

 

SHARP

 

BLADES

 

MAY

 

CAUSE

 

INJURY! 

 
 

 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands