BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 50

Page: 50 / 183

Maintenance

5-6

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Disassembly of Handpiece

(Continued)

Step 3: Remove Blade:



Hold the tool with
the blade side up.



Loosen only the left
cover retaining screw.

NOTE

A slight tension on the left

cover screw will allow the blade
housing to stay open on its own.



Insert a screwdriver into the housing
slot.



Using the frame as the support point,
spread
open the housing, just far enough to
remove the blade.



Carefully remove the blade.

Left Cover
Retaining
Screw

Screwdriver

Left Cover
Retaining
Screw

Pivot Support
Point

Housing
Slot

Screwdriver

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands