manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 77

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-33 

 

Assembly of TRIMVAC

®

 AMX Handpiece   

Prior to assembly, be certain all parts are clean and have been inspected for wear per Section 5. 
 

Step 1:  Attach Frame to Power Unit: 

 

 

Slide the spacer ring onto the frame, small end 
first. 

 

While holding the Whizard

® 

AirMax MACH 3 

frame, align the pin in the power unit with one of 
the notches on the frame. 

 

The frame is designed with multiple notches to 
allow the head to be adjusted to the most 
comfortable position for the operator 

 

 For the initial adjustment position, the short 
groove on the power unit should be facing up. 

 

Insert the attachment screw in the frame. 

 

Tighten the attachment screw 

firmly,

 using 

the supplied hex wrench. 

 

NOTE:

  

Recommended torque of 115-140 lb-in (13-16 N-m).

 

 

Step 2:  Install Drive Adapter: 

 

 

Insert the drive adapter and align the square end 
with the square hole in the power unit. 

 

The drive adapter should drop in with no pressing 
force required. 

 

The retaining ring will sit flush against the 
attachment screws when properly inserted. 

 
 
 
 
 

 

 

 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands