manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 44

 

 

Instructions for Operation

 

 

4-20 

Instructions for Operation 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Blade Changing 

(Continued) 

 

 

Loosen the left cover retaining screw to allow the housing to close. 

 

Tighten the right cover retaining screw. 

 

With left cover retaining screw ½ turn loose, adjust housing for proper fit. 

 

Gently pry the housing open until the blade rotates freely and has enough clearance to 
allow the blade to move forward and backward in the housing.  Only a slight amount of 
movement is necessary.  

 

Tighten the cover retaining screws to the recommended torque. 

 

NOTE:  

Recommended torque of 30-40 lb-in (3.4-4.5 N-m). 

IMPORTANT:  

Be sure that the blade is free to move in the housing.  If the blade does 

not move freely, it may cause the trimmer to overheat. 

 

 

Left Cover
Retaining
Screw

Screwdriver

Left Cover
Retaining
Screw

Pivot Support
Point

Housing
Slot

Screwdriver

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands