manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 106

 

 Maintenance

 

 

5-62 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Assembly of Air Motor 

 

Step 1:  Install Rotor 

 

Insert the bearing into the lower bearing plate. 

 

Place the lower bearing plate, with bearing, 
in the air motor assembly tool.  Line up the 
pin in the lower bearing plate with the 
clearance hole in the air motor assembly tool. 

 

Insert the spacer into the lower bearing plate. 

 

Insert the small shaft of the rotor into the 
spacer. 

 

Slide the bearing tool over the rotor shaft. 

 

Using a hammer, tap the bearing tool until 
the rotor is fully seated in the lower bearing 
plate. 

 

 

 

  

 

Bearing

Tool

Rotor

 

Lower Bearing
Plate with Bearing

Spacer

Air Motor
Assembly Tool

 

Bearing 

Lower Bearing 

Plate 

Lower Bearing 

Plate with 

Bearing 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands