BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 48

Page: 48 / 183

Maintenance

5-4

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Disassembly of Handpiece

Step 1: Remove Handpiece from Hose Assembly:



While holding the handpiece, grip the knob assembly with the opposite hand.



Rotate the knob assembly 90° and pull the hose assembly from the handpiece.

NOTE:

The lever will rotate toward the grease cup for right-handed models,

and away from the grease cup for left-handed models.



Place the cap over the end of the handpiece to protect the handle and protect the motor
from water damage.

Lever

Grease Cup

Knob

Assembly

Handpiece

Cap

Handpiece

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands