manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 61

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-17 

 

Assembly of Handpiece 

(Continued)

 

 

Step 2:  Install Drive Adapter 

 

Insert drive adapter and align the square 
end with the square hole in the power 
unit. 

 

Drive adapter should drop in with no 
pressing force required. 

 

The retaining ring will sit flush against 
the attachment screw when properly 
aligned. 

 

 

 

 

 
 

Step 3:  Install Bearing 

 

Push handpiece bearing into the 
frame bore and align the bearing flat 
with the frame flat. 

 

The bearing should go in with 
minimal effort and not require 
pressing. 

 

Do not force the bearing in.  If the 
bearing does not go in easily, check 
frame and bearing for damage or 
build-up. 

 
 
 
 
 

 

 

Drive Adapter 

Retaining Ring 

Bearing 

Bearing Flat 

Frame Flat 

Frame 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands