BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 33

Page: 33 / 183

Instructions for Operation

Manual No. 188000
September 1, 2009

Instructions for Operation
Whizard

AirMax MACH 3 Operating Instructions and Parts

List

4-9

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 9: Install Depth Gauge (Optional)



Loosen depth gauge mounting screws.



Slide depth gauge onto the cover.



Adjust the depth gauge to the desired height.



(See Depth Gauge Adjustment for more information)



Tighten the depth gauge mounting screw(s).

Model Shown is

880-B

Depth Gauge Assembly

Depth Gauge
Mounting
Screws

Cover

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands