manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 31

 Instructions for Operation 

 

 

Manual No.  188000  
September 1, 2009 

 Instructions for Operation  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

4-7 

 

Power Unit / Head Assembly - Attachment and Adjustment 

(Continued)

 

 

Step 6:  Install Pinion 

 

Insert the pinion into the bearing bore. 

 

The pinion should go in with minimal 
effort and not require pressing. 

 

Do not force the pinion into the 
bearing.  If the pinion does not go in 
easily, check bearing and pinion for 
damage or build-up. 

 

The pinion should sit flush against the 
bearing.  If the pinion does not, rotate 
the pinion to seat it flush with the 
bearing. 

 

 

STEP 7:  Install Cover And Blade 

Housing 

 

Set the blade housing on the 
frame and place the cover plate 
over the blade housing. 

 

While holding the cover plate 
firmly against the housing and 
frame, start the two cover 
retaining screws. 

 

Thread the cover retaining 
screws in, leaving a slight 
tension to allow for blade 
adjustment. 

 

 

 

Pinion 

Bearing 

Cover  

Plate 

Cover 
Retaining 
Screw (2) 

Frame 

Blade Housing 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands