BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 86

Page: 86 / 183

Maintenance

5-42

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Assembly of TRIMVAC

AMX Handpiece

(Continued)

Step 8: Install Vacuum Hose Bracket:



Slide the hose bracket onto the power unit.



Align the flat on the vacuum hose bracket with the lever relief groove on the power unit.



Tighten the hose bracket screws.

Step 9: Attach Whizard

AirMax MACH 3 Hose to Power Unit:



Align the pins in the hose assembly with the
grooves on the power unit.



Slide the power unit into the hose assembly.



Rotate the power unit 90º.



The lever will rotate toward the bottom of the
tool.

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands