manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 93

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-49 

 

Inspection and Maintenance of Power Unit

 (

Continued

) 

 

Air Motor 

 

Clean all build-up out of the inlet and exhaust ports. 

 

Inspect the air motor for the following and replace or repair the air motor if damage is detected.  
(See Air Motor Maintenance Section to repair the air motor). 

 

Check for worn or chipped teeth.  Worn out teeth are indicated by rounded off or pointed 
tops on the teeth. 

 

Look for cracked or broken gear teeth. 

 

Inspect the upper bearing plate I.D. and O.D. for nicks, dents, or wear.   

 

Inspect the vanes for chipped or broken tips by looking through the exhaust ports and 
rotating the shaft to see all five vanes. 

 

Inspect the guide pin to verify it is not bent.

 

 

 

The shaft should rotate freely. 

 

Lubricate the air motor with mineral oil through the exhaust ports. 

 

 

 

Exhaust

Ports

Shaft

Guide

Pin

Vane (5)

Inlet  

Port 

Gear Teeth

Upper Bearing
Plate

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands