BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 26

Page: 26 / 183

Instructions for Operation

4-2

Instructions for Operation
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Optional Thumb Support

Your Whizard

AirMax MACH 3 Trimmer has been supplied with a spacer ring and an

optional thumb support. If using the optional thumb support, the operator’s thumb
should be fully supported and rest comfortably in the support. The thumb support has
been optimized to fit most hands comfortably.

NOTE

If the operator normally wears a glove, this process

should be done with the glove(s) used in normal operation.

We do not recommend the use of Nitrile gloves in direct

contact with the Whizard

AirMax MACH 3 handles because

the gloves may become slippery.

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard AirMax MACH 3

Reviews:

Brands by name

Popular brands