manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 54

 

 Maintenance

 

 

5-10 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Inspection and Maintenance of Handpiece 

 

 

 

W A R N I N G  

 

 

 

SHARP BLADES MAY CAUSE CUT INJURY! 

 

ALWAYS

 

DISCONNECT

 

THE

 

AIR

 

SUPPLY

 

PRIOR

 

TO

 

SERVICING. 

 

FOR

 

PROPER

 

PROTECTION

 

OF

 

HANDS,

 

A

 

PROTECTIVE

 

GLOVE

 

SHOULD

 

BE

 

USED

 

WHEN

 

OPERATING

 

THIS

 

EQUIPMENT

 

AND

 

DURING

 

THE

 

HANDLING

 

OF

 

BLADES. 

 

Blade 

 

Inspect the cutting edge height with a Whizard

®

 blade gauge. 

 

Check for worn or chipped teeth. 

 

Check for damage to the cutting edge. 

 

Blade Housing 

 

Inspect inner diameter of the housing for wear. 

 

Look for evidence of the blade rubbing the outer wall of the housing. 

 

When holding the housing with a new blade installed, if the split in the housing touches 
the other side, and the blade is still loose, the housing needs to be replaced.  If a gap is 
seen, the housing is acceptable. 

 

 

 

Gap – 

Housing is Acceptable 

No Gap – 

Replace Housing 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands