manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 94

 

 Maintenance

 

 

5-50 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Inspection and Maintenance of Power Unit

 (

Continued

) 

 

Adapter Plate 

 

Inspect the adapter plate for cracks or chips.  Replace the adapter plate if damaged. 

 

Inspect o-ring for nicks, cuts or tears.  Replace the o-ring if damaged. 

 
 
 
 
 
 
 
 
 

 

 
 
 
Muffler 

 

Inspect the muffler for broken or protruding wires.  Replace the muffler if damaged. 

 

Muffler may be cleaned with parts cleaner to remove build-up.  Replace muffler if 
excessive build up prevents proper cleaning. 

 

 

Retainer 

 

Inspect the retainer for cracks or chips.  Replace the retainer if damaged. 

 

Inspect the retainer threads for damage.  Replace the retainer if damaged. 

 

Adapter 

Plate 

O-Ring 

Note: 

 

Do not clean the muffler 
while it is installed in the 
power unit. 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands