manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 12

 

 Designated Use 

 

2-2 

 Designated Use  
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Recommended Operation 

 
Whizard

® 

AirMax MACH 3 Trimmers are made for several recommended operations.  Assure 

that you are using the correct tool for your specific application.  The following recommendation 
list is not intended to be a total and comprehensive listing, but is offered as a guide.  Additional 
applications are possible. 
 

Model 350 / 360 

 

BEEF 

PORK 

POULTRY 

 

Cartilage Removal 

 

Liver Spotting 

 

Bone Trimming 

 

Strip Intestine 

 

Button Bones 

 

Bone Trimming 

 

Spotting Livers / Removing 
Gall Sacks 

 

Turkey Breast 

 

Turkey Necks 

 

Chicken Backs 

 

Turkey Thighs 

 

Turkey Cage 

 

Oil Sacks 

 
 

Model 620 

 

BEEF KILL/OFFAL 

POULTRY 

PORK KILL/OFFAL 

 

Removing Lean from 
Heads 

 

De-Veining Livers 

 

Removing Lean from Turkey 
Carcasses  

 

Removing Lean from Turkey 
Necks  

 

Removing Oil Sacks 

 

Removing Eyelids 

 

Cleaning Stick Wounds 

 

Removing Eardrums 

 

Removing Lean from Heads 

 

Spotting Livers / Removing 
Gall Sacks 

 
 
BEEF BONING / FABRICATION 

 
 
PORK CUT 

 

Removing Lean from Bones, Especially: 

- Neck Bones - Atlas Bones 
- Chine Bones from Strips or Rib Eyes 
- Pelvic Bones / Aitch Bones 
- Rib Cages 
- Blade Bones 
- Strip Bones 
- Feather Bones 

 

Trimming Neck Bones 

 

Removing Lean from Bones 

 

Removing Tails 

 
 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands