manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 62

 

 Maintenance

 

 

5-18 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Assembly of Handpiece 

(Continued)

 

 

Step 4:  Install Pinion 

 

Insert the pinion into the bearing bore. 

 

The pinion should go in with minimal 
effort and not require pressing. 

 

Do not force the pinion into the 
bearing.  If the pinion does not go in 
easily, check bearing and pinion for 
damage or build-up. 

 

The pinion should sit flush against the 
bearing.  If it does not, rotate the 
pinion to seat it flush with the bearing. 

 

 
 
 
 

Step 5:  Install Cover and Blade Housing 

 

Set the blade housing on the frame 
and place the cover plate over the 
blade housing. 

 

While holding the cover plate firmly 
against the housing and frame, start 
the two cover mounting screws. 

 

Thread the cover retaining screws in, 
leaving a slight tension to allow for 
blade adjustment. 

 

 

 

 

 

 

Pinion 

Bearing 

Cover  

Plate 

Cover 
Retaining 
Screw (2) 

Frame 

Blade Housing 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands