manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 91

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-47 

 

Inspection and Maintenance of Power Unit 

 
Inspection and maintenance should be performed after every 80 hours of use. 

 

Handle 

 

Clean the handle with warm soapy water and a soft brush.  Remove any build up from the 
grooves.  Rinse the handle and dry thoroughly. 

 

Inspect the handle for the following and replace if damage is detected. 

 

Inspect the handle grip for tears, cuts, or wear. 

 

Inspect the handle grooves for nicks or wear. 

 

Inspect the handle I.D. for dents. 

 

Grip

Groove (2)

 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands