manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 41

 Instructions for Operation 

 

 

Manual No.  188000  
September 1, 2009 

 Instructions for Operation  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

4-17 

 

 

Whizard

®

 Special 

Steel 

Blade Steeling 

(Continued) 

 

Steeling for Model:  360

 

 

 

Steel the outside edge of the blade by laying the special Whizard

®

 steel flat against the 

outside surface of the blade.  Be sure to hold the steel flat and across the centerline of the 
blade to prevent “rounding off” or rolling of the edge. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Steel the inside of the blade by placing the cone shaped tip of the Whizard

®

 special steel 

on the inside edge of the blade.  Do not touch the blade with the shaft of the Whizard

®

 

special steel. 

 
 

 

*

Note

:  Do not

 

touch the steel to 
the blade.

 

Whizard

®

 Special 

Steel 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands