manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 112

 

 Maintenance

 

 

5-68 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Quick Start Valve and Hose Assembly Maintenance 

 

Required Tools for Quick Start Valve and Hose Assembly 
Maintenance 

 

1 – 1/2” Open End Box Wrench 
1 – 9/16” Open End Box Wrench 
 

Inspection of Valve and Hose Assembly 

 

Quick Start Valve and Hose Assembly 

 

Connect the valve and hose assembly to the FRL at 
90-100 psi. 

 

If air leaks around the housing plug, replace the o-ring 
on the housing plug 

 

If air leaks around the valve stem, replace the lower 
valve stem o-ring. 

 

If air leaks through the valve tube, replace the upper 
valve stem o-ring. 

 

If replacing the valve stem o-rings does not fix the air leak, 
replace the valve body assembly 

 

If the valve tube is dented, nicked, or scratched, replace the 
valve body assembly. 

 

If air can be felt leaving the muffler, replace the hose 
assembly. 

 

If the exhaust hose is cut, torn, or nicked, replace the 
exhaust hose. 

 

If the muffler is dirty or clogged, replace the muffler. 
 

 

 

 

Housing Plug 

Valve Stem 

Muffler 

Exhaust Hose 

Valve Tube 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands