manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Operating Instructions & Parts List Manual

Share
Download
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Operating Instructions & Parts List Manual Download Page 59

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-15 

 

 

Thumb  
Support 

Tab 

Frame 

Notches 

Assembly of Handpiece 

 

Prior to assembly, be sure all parts are clean and have been inspected for wear per Section 5. 

 

Step 1:  Attach Head to Power Unit 

 

Select the spacer ring or optional 
thumb support.  

 

If a spacer ring is used:

  Slide the 

spacer ring onto the frame, small end 
first.  

 

 
 

 

 
 
 
 
 
 
 
 

 

If an optional thumb support is used:   

The thumb support should be positioned on the opposite side of the grease cup. 

 

 

Align the thumb 
support tab with a notch 
on the underside of the 
frame and slide the 
thumb support onto the 
frame. 

 

The frame is designed 
with multiple 
notches to allow 
the thumb support 
to be adjusted to the 
most comfortable 
position for the 
operator. 

 

Spacer Ring 

Small End 

Frame 

Summary of Contents for Whizard AirMax MACH 3
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands